Technical designation of hardware version: H1m13v1e1
Technical designation of last firmware revision: S1m13a1v9
Ordering designation: 3000-U13-XX
Note: This module is obsolete and will be replaced by the following newer module:
|
|
| Abstract | ||||||||
 The module combines 4 Components for sensory supervision and 4 Switching Components. The module evaluates the output voltage of up to 4 attached sensors or switches. Measured values can be read and set points can be defined. There can be an upper and a lower set point for each of the sensor inputs. As a reaction of exceeding or falling below a set point, a Relay Output Component can be switched on. The module provides 4 relays with a switch over contact each for this purpose. Each of the relays can be assigned to a set point by configuration. Furthermore, each set point can be assigned to one of two alarm lines. A RS232 interface allows for controlling additional devices. The module will be delivered with installation instructions. |
||||||||
|
Housing Versions
See also (information becomes more general downwards):
|
| Peripheral devices and accessories | ||||
|
Sensors for the Sensor Input Components
|
||||
|
Temperature Sensor Measuring range temperature: -50..+150 °C / -58..302 °F Ordering designation: 3000-U39-XX
|
|||
|
Climatic Sensor
This climatic sensor enables the measuring of the
humidity and temperature in in-door- and out-door-area. Ordering designation: 3000-U25-XX
|
|||
|
Smoke Detector Photoelectronic smoke detector for the early detection of fires with clear smoke development. Conventional smoke detector without switch-on-control, with alarm latch and alarm indicator. Approval: VDS, LPCB, CNBOP Actions are defined by assigning relay components or alarms and setting proper thresholds. Ordering designation: 3000-U34-XX
|
|||
|
Acceleration/Tilt Sensor It is used to detect vandalism, destruction and theft. The sensor measures acceleration along one axis. Actions are defined by assigning relay components or alarms and setting proper thresholds. Ordering designation: 3000-U38-XX
|
|||
|
Sensor for monitoring and observation of mains voltage Actions are defined by assigning relay components or alarms and setting proper thresholds. Ordering designation: 3000-U40-XX
|
|||
|
Flat Reed Contact Can be used as a digital sensor, e.g. for door monitoring. Ordering designation: 3000-U35-XX
|
|||
|
Prolongation cable for peripherals For prolongation of the connection cable of handles, latches, sensors or actors for connecting a "BOX"- housing version of a Module or a 19 inch Rack Ordering designation (2 meters): on inquiry Ordering designation (5 meters): on inquiry
|
|||
|
Actors for the Relay Output Component
As a reaction of exceeding or falling below a set point of the Sensor Input Component, the Relay Output Component can be switched on if it is assigned to a set point. The relay has a switch over contact which can switch up to 0,5A at 125 V AC / 1A at 30V DC. A connectable unit for switching mains power is available. |
||||
|
Switched socket outlet Electrical outlet unit with a relay contact that switches mains power on/off for plugged devices. It is used as an amplifier for Relay Output Components of ELM modules. Ordering designation: 3000-U41-XX
|
|||
|
Peripherals for the Sensor Input Component as well as the Relay Output Component |
||||
|
Switched socket outlet with observation of mains voltage Electrical outlet unit with a relay contact that switches mains power on/off for plugged devices. It is used as an amplifier for Relay Output Components of ELM modules. In addition, a sensor for observation of mains voltage is contained which can be connected to a Sensor Input Component. Actions are defined by assigning Relay Output Components or alarms and setting proper thresholds. Ordering designation: 3000-U42-XX
|
|||
|
Prolongation cable for peripherals For prolongation of the connection cable of handles, latches, sensors or actors for connecting a "BOX"- housing version of a Module or a 19 inch Rack Ordering designation (2 meters): on inquiry Ordering designation (5 meters): on inquiry
|
|||
|
Peripherals and accessories for the module base platform |
||||
|
Power supply unit 12V DC, 700mA stabilized The module acts as a power feeding point of the ELM system if a power supply unit is connected. Ordering designation: 3000-U03-XX
|
|||
|
CAN/Power cable for connecting "KIT"-modules Cable with CAN-plugs at both ends for connecting two "KIT"-housing versions of ELM modules. The cable is for CAN-Bus signal transmission as well as for power supply. Several standard lengths are available. Other lengths on demand. Ordering designation (0,20 meters): 3000-U17 Ordering designation (0,20 meters): 3000-U18 Ordering designation (0,20 meters): 3000-U19
|
|||
|
CAN/Power cable for connecting "KIT"-modules to "BOX"-modules or to 19 inch Racks Cable with one CAN plug and one RJ11 plug for connecting a "KIT"-housing version of an ELM module to a "BOX"-housing version of a module or to an ELM 19 inch Rack Mount Unit. The cable is for CAN-Bus signal transmission as well as for power supply. Several standard lengths are available. Other lengths on demand. Ordering designation (3,00 meters): on inquiry Ordering designation (5,00 meters): on inquiry
|
|||
|
Patch-Cable Straight-Through 2x RJ45 Patch cable with straight-through wiring for CAN bus chaining of racks and "BOX"-housing versions of modules. Ordering designation: on inquiry
|
|||
